Debinding And Sintering Bell Elevator Furnace For Intermittent Heat Treatment 1750 Ordm C

BF580-17 Bell Furnace for Intermittent Heat Treatment at 1750°C ISO Certified and Durable Construction

The equipment is widely used in high-temperature sintering processes for advanced ceramics, magnetic materials, electronic ceramic components, and other products. The furnace body adopts a fully enclosed structure, enabling atmosphere-controlled sintering within the chamber. It meets the sintering requirements of various workpieces, boasts a broad application market, and offers flexible usage methods. With promising development prospects, it is highly suitable for small-batch production and trial manufacturing in factories and research institutions.

• Rated Temp.: 1700°C
• Max Temp.: 1750°C
• Effective Dimensions: 1200mm×600mm×800mm(D×W×H)
• Heating Method: U-shaped silicon molybdenum heater
• Thermcouple: Type B
• Temperature Control: 2 Points
• Temp. Set Accuracy: ±1°C(flat temp. insulation)
• Temp. Control Mode: control module imported from Japan with PID
• Heat-up Rate: ≤3°C/min
• Temp. Uniformity: ±5°C (empty furnace insulation test 2hours under 1700°C)
• Program Tracking Accuracy: ±2°C (>600°C)
• Furnace Surface Temperature ≤40°C
• Maximum Lifting Trip: 800mm
• Lifting method: Screw driven lifting system
• Loading Weight ≤3000kg (with firing furniture and products)
• Atmosphere Control: two channels of air inlet, each channel of air flow is controlled by the glass rotor flowmeter, single range of 5~50L/min
• Exhaust System: Two exhaust chimneys are installed at the top for exhaust emissions, and the chimney covers can be automatically opened and closed
• Alarm System: with over-temperature, broken couple, overload, over-range, deviation and other sound and light alarm protection function
• Maximum Heating Power: 120kW
• Empty furnace insulation power: ≤60kW
• External Dimensions: 2880×3600×2240mm(D×W×H) (Excluding tracks and control cabinets)
• Appearance Color: Light gray

1. The equipment must be installed indoors, with an ambient temperature of 0°C to 40°C. The indoor environment should be free of flammable gases, corrosive gases, and steam.
2. The equipment requires a floor area of no less than 20 square meters, with a working space length of no less than 5 meters, width of no less than 4 meters, and height of no less than 4 meters. The foundation should be sturdy and level, with the furnace weighing approximately 8000kg.
3. The power supply for this furnace must be a three-phase five-wire AC power line, 160kVA, 220/380±10%VAC, 50±2%Hz. This power line should be dedicated, and large power conversion equipment such as welding machines, electric furnaces, and metal cutting machines should not be connected to this distribution.
4. The equipment must be reliably grounded.
5. Environmental conditions: Temperature 0~40°C, humidity ≤80%RH, no corrosive gases, and no strong airflow disturbances.
6. Gas source conditions: Clean, dry, and oil-free compressed air, with an inlet pressure of 0.4~0.8Mpa and consumption of 10~30m³/h; high-purity oxygen (99.6%) with an inlet pressure of 0.2~0.4Mpa and consumption of 10~30m³/h.
7. Ventilation system: Non-contact connection to the user's exhaust system, with an exhaust capacity greater than 50m³/h.
8. Floor requirements: Level, with no significant vibrations, and a load-bearing capacity of >1000Kg/m².
9. Power conditions: Capacity greater than 160kVA, three-phase five-wire, voltage 220/380V, frequency 50Hz; live wires: yellow, green, red; neutral wire: blue; ground wire: yellow-green.
10. Installation site: 6000mm x 4000mm x 4000mm (D x W x H), with an installation area greater than 24m².